DIY DVD Shelf Project (Part 2)

rp_DIYDVDShelfProject-6_zpsd83034d9.jpg

A few weeks ago, I gave an overview of our DIY DVD shelves. I described different options we tried, how we almost gave up on the whole project, and then how we finally found the perfect material for the shelving … Select Pine Board from Home Depot.

Today we’re back and ready to provide the nitty gritty details.  (Again, apologies for the lighting in these photos.  We have virtually no natural light in our basement.  No windows, and the french doors are actually covered by a deck, which blocks even more light! Better lighting options, including some recessed lighting, are on our master home renovation list!)

After we took some measurements, we determined the number of Select Pine Boards we would need. Our wall was 147 inches wide and 90 inches tall. We’d have to make a few cuts, but luckily not too many.

Here was the big pile of Select Pine Boards before we got started!

 photo DIYDVDShelfProject-6_zpsd83034d9.jpg

First, we did an entire test row. We installed a row of brackets (in our case, we were using corner braces which worked great, and were much cheaper compared to normal brackets.)

 photo DIYDVDShelfProject-10_zpscadfbf80.jpg

We used our laser level to make sure all of the brackets were being screwed in nice and level.

 photo DIYDVDShelfProject-14_zps4c5cef88.jpg

Then, we put shelves on top of the brackets (without screwing them yet). We did this so we could 1) Get a precise measurement of how much we would have to cut off the end of one piece of wood for each row, and 2) To make sure that the shelf was sturdy enough to hold up lots of DVDs!

 photo DIYDVDShelfProject-15_zps271f4f5f.jpg

It worked great!

 photo DIYDVDShelfProject-16_zps1e6eff6f.jpg

Then it was time to install the rest of the brackets. Using an end bracket on one side, Ken worked his way vertically to ensure that each shelf was spaced properly to allow for a DVD case height. We used a piece of scrap wood that was cut to match the average height of a DVD/BluRay case.

 photo DIYDVDShelfProject-19_zpsf4b59533.jpg

 photo DIYDVDShelfProject-22_zps24f02bf2.jpg

(We knew that, thanks to the height of our wall, we wouldn’t be able to get every space evenly, so our top row is a “tall” shelf, meaning that there is more space between the top shelf and ceiling than there is between the other shelves. But that was fine, and it would be great to house some of our taller DVD collections).

Then, thanks to the magic of photography, we had a wall full of brackets!

 photo DIYDVDShelfProject-23_zps35dcebf8.jpg

 photo DIYDVDShelfProject-24_zpsce603e0c.jpg

To get the correct length of our shelves to fit the entire length of the wall, we used, for each row, one 8 foot Select Pine Board uncut, and then a 6 foot Select Pine Board, which we had to cut about 14 inches from for it it fit the wall properly.

So, we placed the 8 foot pine boards on the brackets.

 photo DIYDVDShelfProject-25_zps121ea40c.jpg

Then we measured and cut each piece of 6 foot pine board.

 photo DIYDVDShelfProject-26_zps4c6a0941.jpg

We just used a miter saw to cut the wood. We clamped it down the make the cut easier, but we actually placed the clamp on a scrap piece of wood to avoid denting or damaging the pine board.

 photo DIYDVDShelfProject-27_zps01c76ee2.jpg

 photo DIYDVDShelfProject-28_zps645d21fa.jpg

Unfortunately the miter saw wasn’t quite long enough, and we had to do two separate cuts. (See below where the wood wasn’t completely cut). It still worked fine though, and we didn’t have to use or purchase any additional tools.

 photo DIYDVDShelfProject-29_zps897e29ec.jpg

Then we placed the cut pieces on the brackets and we had a full set of shelves! It was time to start screwing the wood to the brackets!

 photo DIYDVDShelfProject-30_zps4eeb8829.jpg

Side note: We did end up buying a tool that we did not have. It was VERY difficult to use our normal drill to screw the brackets to the wood because the space between the rows of shelves was so tight. We purchased a right angle drill and that made the job INFINITELY easier! We have lamented on previous projects that a right angle drill would have made our work easier, so we definitely see future uses for this tool!

 photo DIYDVDShelfProject-56_zpsdcac4e5b.jpg

 photo DIYDVDShelfProject-55_zps097f187c.jpg

As we progressed, we noticed a problem. Where the two pieces of wood met, they didn’t align after they were screwed to the brackets.

 photo DIYDVDShelfProject-34_zps39bb10bf.jpg

 photo DIYDVDShelfProject-35_zps52a9754e.jpg

After some quick brainstorming, we decided to try simple wood glue to attach the two pieces together, essentially creating one big long piece of wood instead of two separate pieces of wood.  We unscrewed all the screws!

Gluing about 12 feet of wood together was not easy logistically, especially considering our lack of dedicated workspace (like a garage) in our house. But, we ended up rigging together something that worked. We put out two folding tables, and placed the two pieces of wood on the table. The smaller pieces you see sitting on top are just there to weigh the wood down.

 photo DIYDVDShelfProject-36_zpsb356de16.jpg

Ken put a heavy bead of glue on each seam.

 photo DIYDVDShelfProject-37_zpsbf637740.jpg

 photo DIYDVDShelfProject-38_zps1162a2ec.jpg

And then we clamped the two pieces together.

 photo DIYDVDShelfProject-39_zps338cadd5.jpg

 photo DIYDVDShelfProject-40_zps9950d04c.jpg

We let the glue dry overnight, and since we only had space to glue three shelves at a time, this added several days to the project! But, once we would take off the brackets, the two pieces of wood were firmly bonded!

 photo DIYDVDShelfProject-50_zps6a275952.jpg

Once the glue dried, we took a hand sander and sanded off the excess glue.

 photo DIYDVDShelfProject-51_zps94cbf622.jpg

 photo DIYDVDShelfProject-52_zpsaaf4406f.jpg

Then we put the shelves back on the brackets, and continued screwing them in. Ken would use the right angle drill to screw from the bottom, and I would place my hand on top of the shelf so that it wouldn’t move while he was screwing the pieces together.

 photo DIYDVDShelfProject-57_zps98517c4a.jpg

We used these 3/4″ screws to affix the brackets to the wood. (Ken is a huge fan of Robinson screws, also called Square screws, but you can use plain old Phillips screws too).

 photo DIYDVDShelfProject-48_zpsc7e7dae7.jpg

Before long, all the shelves were attached to the brackets and we had nice clean seams where the two pieces of wood met!

 photo DIYDVDShelfProject-59_zps59ab0e07.jpg

 photo DIYDVDShelfProject-58_zpsb6195b03.jpg

 photo DIYDVDShelfProject-60_zpsdd5442a7.jpg

And there you have it! Our completed DIY DVD Wall Shelves!

 photo DIYDVDShelfProject-1_zpscb7a7d7a.jpg

We added some fun stuff to the shelves like my old Atari (on the top shelf) and Ken’s old Game Cube (in the middle) and Super Nintendo (Top Shelf). There’s a few other things too, like the Atari Controller, a Game Boy, and our Apple TV box (that we don’t use anymore).

 photo DIYDVDShelfProject-1_zpscb7a7d7a.jpg

In the future, we may consider staining the wood a darker color, or maybe even spray painting the brackets. But, by the time we finally arrived at a solution that worked after our first several failed attempts, we were in a hurry to get the shelves up on the wall! But all the hard work is done now, like the measuring. Removing items one row at a time to stain or spray paint wouldn’t be too much of a problem.

But for now, we love it as-is! Much better than the old store-bought shelves, don’t you think?

 photo DVDshelves-before_zpse3ffe1b5.jpg

How do you store your DVD collection?

 photo DIYDVDShelf_zpsd60317fe.jpg

5 Comments

  1. Michael Boye Olsen   •  

    Hi. I really like your project, and I’m thinking of doing something similar – I just have one question.

    Do you the angle brackets are in the way of the DVD’s?

    BR,
    Michael.

    • Michael Boye Olsen   •  

      Do you feel that*

    • Melissa   •     Author

      Hi, the brackets we used (link is in the post) are great and don’t interfere with the DVDs at all. They’re not the prettiest brackets in the world, but it doesn’t interfere or block the DVDs like a more decorative bracket with a kind of “crossbrace” normally would. Hope this helps!

      • Michael Boye Olsen   •  

        Thanks for the answer.
        I got another question before I throw myself into it.
        How much space do you have between each shelf? 🙂

  2. Kevin Mccracken   •  

    How many dvds was able to fit on there

Leave a Reply

Your email address will not be published. Required fields are marked *